Polyvinyl Chloride (PVC) and Polymethyl Methacrylate (PMMA / Acrylic) are the two most quoted options for plastic rods and bars in home appliance projects. Both are widely available, but they behave very differently once they are in service.
The notes below come from day to day production and export work with overseas buyers.
This category covers a family of products rather than a single item. In practice a buyer defines plastic rods and bars by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include diameter 6 mm to 500 mm; ground tolerance h9; round, square and hex profiles. Materials most often specified are Polymethyl Methacrylate, Polyoxymethylene, UHMWPE, Polytetrafluoroethylene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the home appliance sector the decision is usually driven by heat resistance and noise control, with colour consistency as a secondary requirement. Typical end uses include washer tubs, refrigerator liners, kettle bodies.
Typical values for a general purpose grade are listed below; filled, stabilised and speciality compounds will differ.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
| Polycarbonate | 1.20 g/cm³ | 55-70 MPa | -40°C to 120°C |
| Polyoxymethylene | 1.41 g/cm³ | 60-70 MPa | -40°C to 100°C |
Polyvinyl Chloride is frequently the default selection here: PVC can be formulated from rigid pipe compound to soft medical grade by changing plasticiser content.
Polyvinyl Chloride grades offer inherently flame retardant, while Polymethyl Methacrylate brings up to 92% light transmission. For home appliance service the difference shows up in creep and in the long term behaviour under load.
The practical decision usually comes down to the service environment: temperature, chemical exposure and expected lifetime.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Use this checklist when comparing two or three supplier quotations.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
If you are planning a new home appliance project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap