Polylactic Acid (PLA) and Low Density Polyethylene (LDPE) are the two most quoted options for plastic films and flexible packaging in logistics and warehousing projects. Both are widely available, but they behave very differently once they are in service.
The notes below come from day to day production and export work with overseas buyers.
This category covers a family of products rather than a single item. In practice a buyer defines plastic films and flexible packaging by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include custom printed up to 8 colours; corona treated surface; width up to 3000 mm. Materials most often specified are High Density Polyethylene, Polyethylene Terephthalate, Polypropylene, Polylactic Acid, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the logistics and warehousing sector the decision is usually driven by impact protection and load rating, with stackability as a secondary requirement. Typical end uses include stretch film, returnable pallets, protective dunnage.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| High Density Polyethylene | 0.94-0.97 g/cm³ | 20-32 MPa | -50°C to 80°C |
| Polyethylene Terephthalate | 1.35-1.40 g/cm³ | 50-70 MPa | -40°C to 70°C |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
Polylactic Acid is frequently the default selection here: PLA is compostable in industrial facilities, not in a backyard heap, so label it carefully.
Polylactic Acid grades offer bio-based and industrially compostable, while Low Density Polyethylene brings very flexible and soft. For logistics and warehousing service the difference shows up in creep and in the long term behaviour under load.
In short: choose the first option when stiffness, heat and dimensional stability dominate; choose the second when impact, cost and processing speed matter more.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Work through these points in order and most specification mistakes disappear.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
If you are planning a new logistics and warehousing project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap