Polystyrene (PS / HIPS) and Polylactic Acid (PLA) are the two most quoted sheet materials for thermoformed packaging inserts and dividers in toys and games projects. Both run well on standard thermoforming equipment, but they differ in clarity, toughness and sealing.
Use it as a working checklist when you write your next enquiry.
This category covers a family of products rather than a single item. In practice a buyer defines thermoformed packaging inserts and dividers by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include custom footprints to fit outer cartons; 2 to 48 cavity layouts; nestable designs. Materials most often specified are Polyethylene Terephthalate, Polylactic Acid, Recycled PET, Polystyrene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the toys and games sector the decision is usually driven by child safety and presentation, with durability as a secondary requirement. Typical end uses include craft set packs, game inserts, collector windows.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polylactic Acid | 1.24 g/cm³ | 50-60 MPa | up to 55°C (HDT) |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
| Recycled PET | 1.35-1.40 g/cm³ | 45-65 MPa | -40°C to 70°C |
Polystyrene is frequently the default selection here: HIPS is the default thermoforming sheet for food packaging and appliance liners.
Polystyrene grades offer rigid and glossy, while Polylactic Acid brings bio-based and industrially compostable. For toys and games service the difference shows up in chemical resistance and in the long term behaviour under load.
The practical decision usually comes down to the service environment: temperature, chemical exposure and expected lifetime.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Each step below has its own control points, and skipping one of them is where most defects start.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Use this checklist when comparing two or three supplier quotations.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Standard packing is export cartons on fumigation-free pallets, with custom labelling, barcode and retail packing available. We also handle consolidated containers and door to door delivery.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
Our team supplies thermoformed packaging inserts and dividers to toys and games customers worldwide, with samples, material certificates and full inspection reports available before mass production.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap