If you specify Polylactic Acid (PLA) for high cavity count thin gauge packaging, a handful of properties decide whether the part survives forming and service. These are the values worth checking on every data sheet.
Everything here can be checked on a real sample before you commit to a production order.
This category covers a family of products rather than a single item. In practice a buyer defines high cavity count thin gauge packaging by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include nest ratios above 3:1; gauge 0.20 to 0.50 mm; high speed trim in line. Materials most often specified are Polypropylene, Polyethylene Terephthalate, Polylactic Acid, Polystyrene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the food and beverage sector the decision is usually driven by food contact compliance and migration limits, with seal integrity as a secondary requirement. Typical end uses include takeaway containers, fresh produce punnets, bakery inserts.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polyethylene Terephthalate | 1.35-1.40 g/cm³ | 50-70 MPa | -40°C to 70°C |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
| Polylactic Acid | 1.24 g/cm³ | 50-60 MPa | up to 55°C (HDT) |
Polylactic Acid is frequently the default selection here: PLA is compostable in industrial facilities, not in a backyard heap, so label it carefully.
These figures are typical for commercial grades and should be confirmed against the supplier's certificate for your specific lot.
Density 1.24 g/cm³, tensile strength 50-60 MPa, continuous service temperature up to 55°C (HDT) and melt range 150-170°C are the four values to circle on the data sheet. Everything else is secondary for most food and beverage projects.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Each step below has its own control points, and skipping one of them is where most defects start.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Work through these points in order and most specification mistakes disappear.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
Standard packing is export cartons on fumigation-free pallets, with custom labelling, barcode and retail packing available. We also handle consolidated containers and door to door delivery.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.
If you are planning a new food and beverage project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap