High Density Polyethylene (HDPE) and Polypropylene (PP) are the two most quoted sheet materials for twin sheet thermoformed products in logistics and warehousing projects. Both run well on standard thermoforming equipment, but they differ in clarity, toughness and sealing.
This guide is written for engineers, purchasers and project managers who need a practical answer, not a resin data sheet.
This category covers a family of products rather than a single item. In practice a buyer defines twin sheet thermoformed products by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include large panels over 2000 mm; integrated mounting bosses; gauge 2.0 to 8.0 mm. Materials most often specified are PC/ABS Alloy, High Density Polyethylene, Acrylonitrile Butadiene Styrene, Polycarbonate, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the logistics and warehousing sector the decision is usually driven by stackability and returnability, with traceability as a secondary requirement. Typical end uses include returnable trays, bakey distribution crates, dunnage trays.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| High Density Polyethylene | 0.94-0.97 g/cm³ | 20-32 MPa | -50°C to 80°C |
| Acrylonitrile Butadiene Styrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 80°C |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
High Density Polyethylene is frequently the default selection here: HDPE combines toughness with chemical inertness, which is why it dominates pipe and tank markets.
High Density Polyethylene grades offer high impact strength even at low temperature, while Polypropylene brings lowest density among commodity plastics. For logistics and warehousing service the difference shows up in creep and in the long term behaviour under load.
Both materials can be validated quickly with a small sample run, which is the cheapest way to settle the argument for your own application.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Use this checklist when comparing two or three supplier quotations.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
Standard packing is export cartons on fumigation-free pallets, with custom labelling, barcode and retail packing available. We also handle consolidated containers and door to door delivery.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
If you are planning a new logistics and warehousing project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap