If you specify Polycarbonate (PC) for returnable and reusable thermoformed trays, a handful of properties decide whether the part survives forming and service. These are the values worth checking on every data sheet.
Use it as a working checklist when you write your next enquiry.
This category covers a family of products rather than a single item. In practice a buyer defines returnable and reusable thermoformed trays by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include stack and nest configurations; RFID and barcode options; washable designs. Materials most often specified are Acrylonitrile Butadiene Styrene, Polyethylene Terephthalate, Polycarbonate, Polypropylene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the automotive and mobility sector the decision is usually driven by dimensional stability and heat resistance, with impact strength as a secondary requirement. Typical end uses include dunnage trays, commercial vehicle trim, line side trays.
These figures are typical for commercial grades and should be confirmed against the supplier's certificate for your specific lot.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polyethylene Terephthalate | 1.35-1.40 g/cm³ | 50-70 MPa | -40°C to 70°C |
| Polycarbonate | 1.20 g/cm³ | 55-70 MPa | -40°C to 120°C |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
Polycarbonate is frequently the default selection here: PC replaces glass where impact safety matters, but it needs a hard coat for abrasion resistance.
Typical values for a general purpose grade are listed below; filled, stabilised and speciality compounds will differ.
Density 1.20 g/cm³, tensile strength 55-70 MPa, continuous service temperature -40°C to 120°C and melt range 260-300°C are the four values to circle on the data sheet. Everything else is secondary for most automotive and mobility projects.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Work through these points in order and most specification mistakes disappear.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
If you are planning a new automotive and mobility project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap