Polyethylene Terephthalate (PET) and Polyether Ether Ketone (PEEK) are the two most quoted options for anti-static and ESD plastic products in textile and garment projects. Both are widely available, but they behave very differently once they are in service.
This guide is written for engineers, purchasers and project managers who need a practical answer, not a resin data sheet.
This category covers a family of products rather than a single item. In practice a buyer defines anti-static and ESD plastic products by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include surface resistivity 10^6 to 10^9 ohm/sq; transparent conductive coatings; carbon filled and permanent antistat grades. Materials most often specified are Polyethylene Terephthalate, Polycarbonate, Acrylonitrile Butadiene Styrene, Polyether Ether Ketone, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the textile and garment sector the decision is usually driven by flexibility and abrasion resistance, with colour fastness as a secondary requirement. Typical end uses include elastic tapes, fibre and filament, zipper components.
Typical values for a general purpose grade are listed below; filled, stabilised and speciality compounds will differ.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polycarbonate | 1.20 g/cm³ | 55-70 MPa | -40°C to 120°C |
| Polyether Ether Ketone | 1.32 g/cm³ | 90-100 MPa | -50°C to 250°C |
| Polyethylene Terephthalate | 1.35-1.40 g/cm³ | 50-70 MPa | -40°C to 70°C |
Polyethylene Terephthalate is frequently the default selection here: High IV PET resin is the reason a 1.5 L bottle can be light yet hold carbonation pressure.
Polyethylene Terephthalate grades offer excellent barrier to CO2 and moisture, while Polyether Ether Ketone brings retains strength at 250°C. For textile and garment service the difference shows up in chemical resistance and in the long term behaviour under load.
The practical decision usually comes down to the service environment: temperature, chemical exposure and expected lifetime.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Work through these points in order and most specification mistakes disappear.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
If you are planning a new textile and garment project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap