If you specify Polystyrene (PS / HIPS) for clamshell blister packaging, a handful of properties decide whether the part survives forming and service. These are the values worth checking on every data sheet.
Use it as a working checklist when you write your next enquiry.
This category covers a family of products rather than a single item. In practice a buyer defines clamshell blister packaging by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include gauge 0.30 to 0.80 mm; full colour printed inserts; snap lock, button lock and RF seal closures. Materials most often specified are Polypropylene, Recycled PET, Polyethylene Terephthalate, Polystyrene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the retail and merchandising sector the decision is usually driven by shelf presentation and print quality, with stack strength as a secondary requirement. Typical end uses include promotional packs, pegboard blisters, dump bins.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
| Polyethylene Terephthalate | 1.35-1.40 g/cm³ | 50-70 MPa | -40°C to 70°C |
| Polystyrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 70°C |
Polystyrene is frequently the default selection here: HIPS is the default thermoforming sheet for food packaging and appliance liners.
These figures are typical for commercial grades and should be confirmed against the supplier's certificate for your specific lot.
Density 1.04-1.06 g/cm³, tensile strength 30-50 MPa, continuous service temperature -20°C to 70°C and melt range 180-240°C are the four values to circle on the data sheet. Everything else is secondary for most retail and merchandising projects.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
The route below is the one most factories use for this type of part.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Work through these points in order and most specification mistakes disappear.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
If you are planning a new retail and merchandising project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap