Polylactic Acid (PLA) and Polypropylene (PP) are the two most quoted sheet materials for thermoformed deli and food containers in logistics and warehousing projects. Both run well on standard thermoforming equipment, but they differ in clarity, toughness and sealing.
Everything here can be checked on a real sample before you commit to a production order.
This category covers a family of products rather than a single item. In practice a buyer defines thermoformed deli and food containers by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include round, oval and rectangular formats; leak resistant lid fit; in mould labelling options. Materials most often specified are Polypropylene, Polylactic Acid, Polyethylene Terephthalate, Polystyrene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the logistics and warehousing sector the decision is usually driven by stackability and returnability, with traceability as a secondary requirement. Typical end uses include picking trays, parts supermarket trays, returnable trays.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polylactic Acid | 1.24 g/cm³ | 50-60 MPa | up to 55°C (HDT) |
| Polystyrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 70°C |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
Polylactic Acid is frequently the default selection here: PLA is compostable in industrial facilities, not in a backyard heap, so label it carefully.
Polylactic Acid grades offer bio-based and industrially compostable, while Polypropylene brings lowest density among commodity plastics. For logistics and warehousing service the difference shows up in creep and in the long term behaviour under load.
In short: choose the first option when stiffness, heat and dimensional stability dominate; choose the second when impact, cost and processing speed matter more.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Use this checklist when comparing two or three supplier quotations.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
If you are planning a new logistics and warehousing project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap