Design Guide for HDPE Industrial Dunnage and Handling Trays in electronics and electrical: Draft, Radii and Draw Ratio

Thermoforming rewards designs that respect how a heated sheet stretches. These rules prevent most tooling rework and most thickness complaints.

This guide is written for engineers, purchasers and project managers who need a practical answer, not a resin data sheet.

Product Overview

This category covers a family of products rather than a single item. In practice a buyer defines industrial dunnage and handling trays by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include gauge 1.5 to 8.0 mm; custom cavity layouts; ESD and conductive grades. Materials most often specified are High Density Polyethylene, Polycarbonate, Polypropylene, Acrylonitrile Butadiene Styrene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.

In the electronics and electrical sector the decision is usually driven by ESD protection and dimensional accuracy, with cleanliness as a secondary requirement. Typical end uses include accessory blisters, battery packs, connector carriers.

Key Material Properties

The table below summarises the values that usually decide the material choice.

High Density Polyethylene is frequently the default selection here: HDPE combines toughness with chemical inertness, which is why it dominates pipe and tank markets.

Design Rules for Thermoformed Parts

Apply these points before the tool is cut; after that every change costs tooling and time.

• Design uniform wall thickness by avoiding abrupt depth changes in the same cavity.
• Leave a flat sealing flange of at least 6 mm when the pack has to be heat sealed or lidded.
• Keep the draw ratio moderate: deep cavities thin the sheet and force you to start with a thicker gauge.
• Make corner radii at least equal to the sheet thickness; sharp corners are where holes start.
• Use a draft angle of at least 3 degrees per side so the part releases without vacuum locks.
• Avoid undercuts unless the tool has moving sections, which adds cost to every cycle.

Send these rules to your designer together with the sheet gauge and the target cycle time; most tooling modifications come from ignoring draft and corner radii.

Common Grades and Variants

• Polypropylene based: lowest density among commodity plastics
• Polycarbonate based: outstanding impact strength (250x glass)
• Polyethylene Terephthalate based: excellent barrier to CO2 and moisture
• Acrylonitrile Butadiene Styrene based: high impact toughness

Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.

Processing and Finishing Options

Each step below has its own control points, and skipping one of them is where most defects start.

• Welding
• Cnc trimming
• Twin sheet forming
• Assembly

Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.

How to Specify Industrial dunnage and handling trays Correctly

Work through these points in order and most specification mistakes disappear.

1. specify ESD grade if electronics are handled
2. design locating features that survive repeated use
3. validate washing and drying resistance
4. define the number of returnable trips expected
5. check stack load and conveyor compatibility

Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.

Frequently Asked Questions

What packing and shipping options are available?

Standard packing is export cartons on fumigation-free pallets, with custom labelling, barcode and retail packing available. We also handle consolidated containers and door to door delivery.

What tolerance can be achieved?

Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.

What is the minimum order quantity for industrial dunnage and handling trays?

For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.

Which certifications can you provide?

We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.

Can you produce industrial dunnage and handling trays in High Density Polyethylene?

Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.

Conclusion

Our team supplies industrial dunnage and handling trays to electronics and electrical customers worldwide, with samples, material certificates and full inspection reports available before mass production.