If you specify Polyethylene Terephthalate (PET) for thermoformed lids and domes, a handful of properties decide whether the part survives forming and service. These are the values worth checking on every data sheet.
Use it as a working checklist when you write your next enquiry.
This category covers a family of products rather than a single item. In practice a buyer defines thermoformed lids and domes by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include clear, black and coloured; gauge 0.25 to 0.60 mm; fitting 90 to 260 mm containers. Materials most often specified are Polypropylene, Polystyrene, Polyethylene Terephthalate, Polylactic Acid, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the retail and merchandising sector the decision is usually driven by shelf presentation and print quality, with stack strength as a secondary requirement. Typical end uses include promotional packs, shelf trays, pegboard blisters.
The table below summarises the values that usually decide the material choice.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polystyrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 70°C |
| Polypropylene | 0.90-0.91 g/cm³ | 25-40 MPa | -10°C to 100°C |
| Polylactic Acid | 1.24 g/cm³ | 50-60 MPa | up to 55°C (HDT) |
Polyethylene Terephthalate is frequently the default selection here: High IV PET resin is the reason a 1.5 L bottle can be light yet hold carbonation pressure.
These figures are typical for commercial grades and should be confirmed against the supplier's certificate for your specific lot.
Density 1.35-1.40 g/cm³, tensile strength 50-70 MPa, continuous service temperature -40°C to 70°C and melt range 245-265°C are the four values to circle on the data sheet. Everything else is secondary for most retail and merchandising projects.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
The route below is the one most factories use for this type of part.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
Use this checklist when comparing two or three supplier quotations.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
Our team supplies thermoformed lids and domes to retail and merchandising customers worldwide, with samples, material certificates and full inspection reports available before mass production.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap