If you specify Thermoplastic Elastomer (TPE / TPR) for thermoformed powersports and outdoor panels, a handful of properties decide whether the part survives forming and service. These are the values worth checking on every data sheet.
The notes below come from day to day production and export work with overseas buyers.
This category covers a family of products rather than a single item. In practice a buyer defines thermoformed powersports and outdoor panels by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include textured scratch resistant finishes; large hood and fender panels; UV stable colours. Materials most often specified are Acrylonitrile Butadiene Styrene, Thermoplastic Elastomer, Polypropylene, High Density Polyethylene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the automotive and mobility sector the decision is usually driven by dimensional stability and heat resistance, with impact strength as a secondary requirement. Typical end uses include commercial vehicle trim, dunnage trays, under body shields.
Typical values for a general purpose grade are listed below; filled, stabilised and speciality compounds will differ.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Thermoplastic Elastomer | 0.90-1.30 g/cm³ | 5-30 MPa | -40°C to 100°C |
| Acrylonitrile Butadiene Styrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 80°C |
| High Density Polyethylene | 0.94-0.97 g/cm³ | 20-32 MPa | -50°C to 80°C |
Thermoplastic Elastomer is frequently the default selection here: TPE removes the vulcanisation step, so soft parts come off the press ready to pack.
The table below summarises the values that usually decide the material choice.
Density 0.90-1.30 g/cm³, tensile strength 5-30 MPa, continuous service temperature -40°C to 100°C and melt range 160-220°C are the four values to circle on the data sheet. Everything else is secondary for most automotive and mobility projects.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
Processing method drives both cost and performance, so it should be fixed early in the design.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
These are the criteria that actually predict whether the part will perform in service.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
We can provide ISO 9001 quality system documentation, material certificates, RoHS and REACH statements, and where applicable food contact, flame retardancy or drinking water approvals. Tell us your target market and we will match the document set.
A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.
Our team supplies thermoformed powersports and outdoor panels to automotive and mobility customers worldwide, with samples, material certificates and full inspection reports available before mass production.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap