High Density Polyethylene (HDPE) and Polypropylene (PP) are the two most quoted sheet materials for thermoformed refrigerator liners and door panels in home appliance projects. Both run well on standard thermoforming equipment, but they differ in clarity, toughness and sealing.
Everything here can be checked on a real sample before you commit to a production order.
This category covers a family of products rather than a single item. In practice a buyer defines thermoformed refrigerator liners and door panels by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include gauge 1.5 to 4.0 mm; deep draw geometries; food contact inner surfaces. Materials most often specified are Acrylonitrile Butadiene Styrene, Polystyrene, Polypropylene, High Density Polyethylene, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.
In the home appliance sector the decision is usually driven by deep draw capability and chemical resistance to insulation foam, with surface quality as a secondary requirement. Typical end uses include refrigerator liners, machine covers, door panels.
These figures are typical for commercial grades and should be confirmed against the supplier's certificate for your specific lot.
| Material | Density | Tensile strength | Service temperature |
|---|---|---|---|
| Polystyrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 70°C |
| High Density Polyethylene | 0.94-0.97 g/cm³ | 20-32 MPa | -50°C to 80°C |
| Acrylonitrile Butadiene Styrene | 1.04-1.06 g/cm³ | 30-50 MPa | -20°C to 80°C |
High Density Polyethylene is frequently the default selection here: HDPE combines toughness with chemical inertness, which is why it dominates pipe and tank markets.
High Density Polyethylene grades offer high impact strength even at low temperature, while Polypropylene brings lowest density among commodity plastics. For home appliance service the difference shows up in creep and in the long term behaviour under load.
The practical decision usually comes down to the service environment: temperature, chemical exposure and expected lifetime.
Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.
The route below is the one most factories use for this type of part.
Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.
These are the criteria that actually predict whether the part will perform in service.
Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.
Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.
Yes. Standard samples are normally free of charge and shipped within three working days; custom samples are charged at cost and credited against the first production order.
For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.
Standard packing is export cartons on fumigation-free pallets, with custom labelling, barcode and retail packing available. We also handle consolidated containers and door to door delivery.
Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.
If you are planning a new home appliance project, send us your drawing, annual volume and target properties, and we will come back with a material proposal, a tooling plan and a budget quotation.
Rubber & Plastics © 2026 All Rights Reserved. Yingnet.com — Global B2B trade platform for rubber & plastics manufacturers.
About Us | Contact Us | Help Center | Sitemap