Design Guide for PP Clamshell Blister Packaging in electronics and electrical: Draft, Radii and Draw Ratio

Thermoforming rewards designs that respect how a heated sheet stretches. These rules prevent most tooling rework and most thickness complaints.

Everything here can be checked on a real sample before you commit to a production order.

Product Overview

This category covers a family of products rather than a single item. In practice a buyer defines clamshell blister packaging by three things: the base resin, the format or dimension, and the performance or certification level it has to meet. Typical options in this category include gauge 0.30 to 0.80 mm; snap lock, button lock and RF seal closures; hinged single piece designs. Materials most often specified are Polyethylene Terephthalate, Recycled PET, Polystyrene, Polyvinyl Chloride, and the choice between them changes stiffness, temperature resistance, chemical behaviour and price.

In the electronics and electrical sector the decision is usually driven by ESD protection and dimensional accuracy, with cleanliness as a secondary requirement. Typical end uses include device inserts, battery packs, accessory blisters.

Key Material Properties

These figures are typical for commercial grades and should be confirmed against the supplier's certificate for your specific lot.

Polypropylene is frequently the default selection here: PP is the lightest mainstream packaging resin and keeps its shape under repeated flexing.

Design Rules for Thermoformed Parts

Apply these points before the tool is cut; after that every change costs tooling and time.

• Make corner radii at least equal to the sheet thickness; sharp corners are where holes start.
• Use a draft angle of at least 3 degrees per side so the part releases without vacuum locks.
• Avoid undercuts unless the tool has moving sections, which adds cost to every cycle.
• Leave a flat sealing flange of at least 6 mm when the pack has to be heat sealed or lidded.
• Keep the draw ratio moderate: deep cavities thin the sheet and force you to start with a thicker gauge.
• Add ribs, steps or kiss-offs instead of increasing overall gauge to gain stiffness.

Send these rules to your designer together with the sheet gauge and the target cycle time; most tooling modifications come from ignoring draft and corner radii.

Common Grades and Variants

• Polyvinyl Chloride based: inherently flame retardant
• Polystyrene based: rigid and glossy
• Recycled PET based: lower carbon footprint than virgin resin
• Polypropylene based: lowest density among commodity plastics

Beyond the base resin, most suppliers offer UV stabilised, food contact, flame retardant, anti-static and recycled content versions of the same product. Ask which additive package is included, because it is often the difference between a part that lasts three years and one that lasts ten.

Processing and Finishing Options

The route below is the one most factories use for this type of part.

• Die cutting
• Vacuum forming
• Pressure forming
• Twin sheet forming

Secondary operations such as printing, welding, machining and assembly are often cheaper to do in the same factory, and they reduce the risk of mismatch between components.

How to Specify Clamshell blister packaging Correctly

These are the criteria that actually predict whether the part will perform in service.

1. test the hinge for at least 20 open-close cycles
2. avoid sharp internal corners at the hinge
3. confirm the trim method to avoid sharp edges
4. check the pack passes the retail drop test
5. specify the closure type and tamper evidence level

Send this list to your supplier with the drawing and you will receive comparable quotations from every factory you contact.

Frequently Asked Questions

Can you produce clamshell blister packaging in Polypropylene?

Yes. {mat1} is one of our regular materials for this item, and we can supply virgin, modified and certified grades with full traceability. Material certificates and test reports are issued per batch.

How do you control colour consistency?

Colour is controlled with a masterbatch reference approved by the customer, and every production lot is checked against the approved sample under standard lighting before shipment.

What is the minimum order quantity for clamshell blister packaging?

For standard sizes and colours the minimum is usually one pallet or one production run; for custom tooling the economic minimum depends on the tooling cost amortised over the expected volume. Send us your annual volume and we will calculate the break even point.

How long does tooling and sampling take?

A new tool typically takes 25 to 45 days depending on cavity count and complexity, followed by T1 samples within one week. Existing tools can usually start production within 10 to 15 days of order confirmation.

What tolerance can be achieved?

Standard production tolerance follows the relevant ISO or DIN tolerance class for the process; tighter tolerances are possible after machining or grinding, but they add cost. Define the tolerance only on the functional dimensions.

Conclusion

Share your specification and quantity with us and we will recommend the most cost effective material, tooling route and packing method for your market.